Why Understanding Essential Plumbing Skills is Important For Installing a Bathtub
Why Understanding Essential Plumbing Skills is Important For Installing a Bathtub
Blog Article
We've uncovered this post on Tools You Need to Install a New Bathtub listed below on the net and accepted it made good sense to write about it with you over here.
Setting up a tub isn't exactly brain surgery, however it does call for strong plumbing, woodworking, and also occasionally, tiling skills. Replacing an old bathtub with a new one is also a moderately challenging project. If the old bathtub is conveniently obtainable, the job can move speedily; if you have to open up a wall to eliminate the old bathtub and also position the new tub, the job is a lot harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub and set in the new one. Ensure you have qualified yourself for the task as well as fit trying it. Instead of employing a specialist to take control of a halfway-completed job, it is better to consider using one prior to you start. Chances are you may require a specialist plumber to make tube connections.
This article will certainly aid you install a brand-new bathtub in your shower room if you have actually currently purchased a brand-new bathtub and also don't need to transform the setup of your previous water supply pipelines.
Your tools as well as material list must make up the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the supply of water. After doing so, switch on the taps to drain any type of water staying in the system. The procedure of eliminating the existing taps can be rather troublesome because of the restricted access that is typically the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. When the supply pipes have been removed, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single taps from turning during this process. When the taps have actually been removed, the holes in the bath/basin will have to be cleaned of any kind of old securing substance.
Before proceeding to fit the new faucets, contrast the pipeline connections on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will need decreasing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the mounting hole in the bath/basin ensuring that the washing machines remain in place in between the tap and also the sink. Protect the faucet in position with the manufacturer given backnut. As soon as the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal tap adapters. The former type should be attached to the faucet ends initially, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.
Mounting the Tub
Utilizing the two wooden boards under its feet, put the bath tub in the required setting. The wood boards are useful in evenly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 tiny factors.
The following goal is to make sure that the tub is leveled all round. This can be accomplished by checking the level and also readjusting the feet on the tub until the level reviews level.
To install faucets, fit the bottom of the furthest adaptable tap connector to the ideal supply pipe by making a compression sign up with; then do the same for the various other faucet.
Activate the supply of water and examine all joints and also brand-new pipework for leaks as well as tighten them if essential. Fill up the bath tub and likewise inspect the overflow outlet as well as the normal electrical outlet for leaks.
Ultimately, take care of the bath paneling as described in the supplier's user's manual. Tiling and sealing around the bathtub should wait up until the bath tub has actually been used a minimum of once as this will certainly resolve it right into its last placement.
Planning for the Installment
To start with, the sustaining structure provided with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to make sure that if the faucet features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets system to stop stress on the bath tub.
Fit the adaptable tap connectors to the bottom of the two faucets utilizing 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its last setting.
Tiling Around the Tub
In the area where the bathroom meets the tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a stiff seal, causing the water to permeate the wall between the bathroom and the tiling, causing problems with wetness as well as feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your fixtures and also fittings. They are marketed in tubes as well as cartridges, and are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to always fill up the bathtub with water prior to securing, to allow for the activity experienced when the tub remains in use. The sealant can split fairly early if you do not consider this movement prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily available on the marketplace. It is suggested to fit the tiles using water-resistant or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I have been very involved in How to Install a Bathtub Yourself and I hope you enjoyed my blog post. So long as you appreciated our article kindly make sure you remember to pass it around. Thank-you for your time spent reading it.
Ensure plumbing integrity; reach out. Report this page